Exceptionally high-quality power amplifier featuring ZinAmp's exclusive Simultanious Class A. Delivers up to 150W into 8ohms with Class A sound - heatsink required (0.45K/W).

Ready-built PCB requires output devices and connectors to be purchased separately and soldered on. See datasheet for details

Ready Built:	Quantity: Single £49.00 GBP Pair £95.00 GBP
Bare PCB:	Quantity: Single £9.00 GBP Pair £17.00 GBP

Best-of-breed Lateral MosFET power amplifier featuring Exicon's Lateral MosFETs. Simple to build and setup and requires no biasing. Highly scalable, from 100w to 250w depending on configuration - heatsink required (0.45K/W). Can also be run in bridge mode - see datasheet. Requires -/+48v power supply. Heat-sink Mounting Plate also available

Ready-built PCB requires connectors to be purchased separately and soldered on. See datasheet for details

Ready Built:	Quantity: Pair - 100W £95.00 GBP Pair - 150W £115.00 GBP Pair - 200W £145.00 GBP Pair - 250W £165.00 GBP
Bare PCB:	Quantity: Single £9.00 GBP Pair £17.00 GBP

Minaturised version of our best-of-breed Lateral MosFET power amplifier featuring Exicon's Lateral MosFETs.

Compact board layout allows three of these modules to be slotted onto our 3-way plate amp control board. This is a fully specced class A/B power amp with nothing missing, other than slots for a second pair of LateralFETs. Capable of up to 200wPC into 8ohms when using Exicon double-die LateralFETs. Simple to build and setup and requires no biasing.

Ready Built:	Quantity: Pair - 100W £90.00 GBP Tri - 100W £140.00 GBP Pair - 200W £125.00 GBP Tri - 200W £185.00 GBP
Bare PCB:	Quantity: Single £9.00 GBP Pair £17.00 GBP Tri £25.00 GBP

Complete Amplifier solution for a plate-amp, monoblock or stereo installation. Includes system board and SCA Power Amp module.

Control board includes AC power wiring, soft-start, speaker protection and auto power-off/on. An additional power amp module can be connected to the control board to provide stereo (L & R) channels.

Support for both XLR balanced and RCA unbalanced inputs

Connecting a transformer is simple. Board layout conforms with CE Low Voltage Directive in that primary and secondary AC tracks are appropriately spaced.

Ready Built:	Quantity: Mono £299.00 GBP Stereo - RCA Only £349.00 GBP Stereo - RCA & XLR £539.00 GBP
Bare PCB:	Quantity: Mono £79.00 GBP Stereo - RCA Only £99.00 GBP Stereo - RCA & XLR £169.00 GBP

Power Supply for up to two Power Amps (l & r). Regulated to between 1 and 10mv of ripple, depending on load. Requires 2x2.5A fast blow fuses. Jumper switches for voltage selection of -/+ 42v or -/+ 48v. Can be run up to -/+ 56v with appropriate modification. Protects against chaos of fuse-failure on one rail by automatically reducing the voltage on the other, protecting your precious amplifier!

Requires 220-300VA toroidal transfomer, min: 33-0-33 max: 45-0-45, ideally: 40-0-40. Ready-built PCB requires connectors to be purchased separately and soldered on. See datasheet for details. Heat-sink Mounting Plate also available

Ready Built:	£69
Bare PCB:	£12

Power Supply for up to two Power Amp modules (l & r). Requires 2 x 3A fast blow fuses. RC-snubbed switch terminal allow remote on/off control. Can be run up to -/+ 70vDC with appropriate capacitors fitted. One or two pairs of filter caps can be fitted.

Requires 160-300VA toroidal transfomer, min: 18-0-18 max: 50-0-50. Ready-built PCB requires connectors to be purchased separately and soldered on. See datasheet for details. Heat-sink Mounting Plate also available

Ready Built:	Capacitance: 2 x 6800uF Caps £49.00 GBP 4 x 6800uF Caps £66.00 GBP
Bare PCB:	£12

Protects loudspeakers from start-up thump and from any errant DC offset from the power amp. DC voltage detected in either the left or right channel immediately triggers the audio to be cut in both speakers

Powered by the DC supply from your power amp rails, i.e. requires no additional power supply. Works with a range of voltages from -/+35v to -/+56v

Ready-built PCB requires connectors to be purchased separately and soldered on. See datasheet for details

Ready Built:	£34
Bare PCB:	£9

Heavy duty PCB with terminals for AC transformers and connections to power supplies. Terminals are provided for an AC fuse, On/Off switch and auto-power-off switch. Additional terminals for an AC relay and two thermistors form a "soft-start" feature that protects the on/off switch and other circuitry by limiting inrush current. Can be wired for 220v or 120v DC - see datasheet. Switch nets are snubbed to prevent switch-terminal arcing/pitting

Board layout conforms with CE Low Voltage Directive in that primary and secondary AC tracks are appropriately spaced.

Pre-built PCB includes screw terminal blocks as standard. Please email us if you would like different connectors

Ready Built:	£29	Soft Start: No - £29.00 GBP Yes - £44.00 GBP
Bare PCB:	£8

Heavy duty PCB that separates AC and chassis earth from DC and audio grounds via the diodes of a heavy-duty bridge rectifier.

Current rating: 35A

AC and DC Grounds are separated to eliminate ground loops that may be experienced when connecting other equipment to your amplifier. AC earth and the metal chassis make a direct connection on the Earth Hub to maintain safety

Pre-built PCB includes screw terminal blocks as standard. Please email us if you would like different connectors

Ready Built:	£19
Bare PCB:	£8